Jump to content

Improve your 3D prints

Help, tips & tricks

5,372 topics in this forum

  1. Select What printer to select?

    By johnboyman,   
    • 3 replies
    • 403 views

  2. UM2+ Power Surge? Video Attached.

    By WiseOldOwl,
    • 4 replies
    • 651 views

  3. How to set the height of the nozzle above the heat bed?

    By johnboyman,   
    • 4 replies
    • 702 views

  4. HELP!! please slicing issues

    By Ex7remeSpider,   
    • 0 replies
    • 484 views

  5. Help Improve ABS printing

    By tribrachsolutions,   
    • 3 replies
    • 307 views

  6. Remotely Confirm Build Plate is Clear

    By timmsc,
    • 3 replies
    • 1.4k views

  7. Extruder calibration hell

    By Lukephos,   
    • 6 replies
    • 605 views

  8. Help required - Cura settings

    By Earl,   
    • 0 replies
    • 408 views

  9. PLA- and PET- smoothing with dichloromethane CH2Cl2

    By geert_2,   
    • 12 replies
    • 4.4k views

  10. Why Cura slicing travel speed is much slower than PrusaSlicer? How can I improve the travel speed ?

    By blackgun,   
    • 0 replies
    • 1.2k views

  11. Change Z Offset / Print in the air

    By Erkan3D,   
    • 15 replies
    • 5.9k views

  12. Print quality degradation, advanced maintenance and overhaul

    By pavelr,   
    • 4 replies
    • 413 views

  13. What causes this issue?

    By Buffdude,   
    • 0 replies
    • 304 views

  14. This is a strange one. build plate cooling while printing and print stopping.

    By Twigs,   
    • 1 reply
    • 312 views

  15. Geert Keteleer's Salt Water build-plate adhesion...amazing!

    By nzo,
    • 21 replies
    • 9.5k views

  16. Spiralize outer contour is leaving two shells at layer two

    By LoganHesdemc,   
    • 0 replies
    • 296 views

  17. Help with printing engraved text

    By Nicko_Airbus,   
    • 3 replies
    • 4.3k views

  18. Cura ignores part of model when slicing?

    By Slegnor,   
    • 3 replies
    • 1.3k views

  19. Problem with my print raising up vertically more than it's supposed to during print

    By johnboyman,   
    • 8 replies
    • 531 views

  20. Help with print part of if dissapears when i put on supports

    By johnboyman,   
    • 4 replies
    • 360 views

  21. S5 core seems to be clogged but isn't

    By MichielJacobi,   
    • 9 replies
    • 1.3k views

  22. Horizontal lines on prints Ultimaker S5

    By balint,   
    • 5 replies
    • 968 views

  23. Is Aquasys compatible with PLA ?

    By Nicko_Airbus,   
    • 3 replies
    • 444 views

  24. It was good at first, but then it was a nightmare

    By eric_huang,   
    • 4 replies
    • 742 views

  25. first layer extruder support

    By carminati,   
    • 4 replies
    • 529 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 20 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...