Jump to content

Improve your 3D prints

Help, tips & tricks

5,372 topics in this forum

  1. How to get straight lines instead of zigzag lines?

    By huggibunni,
    • 10 replies
    • 2.8k views

  2. rafts and z-hop

    By kpc,
    • 0 replies
    • 576 views

  3. same Ultimaker S5 - same firmware version - same gcode - different outcomes....??

    By YM3,   
    • 3 replies
    • 493 views

  4. Issues printing with supports - what should I do?

    By monomonster,
    • 1 reply
    • 385 views

  5. Big Problem with shell finish

    By Frutolo,
    • 22 replies
    • 1.4k views

  6. Extrusion problems

    By kirav,
    • 1 reply
    • 249 views

  7. Ultimaker 2 build plate not lowering sufficiently during print

    By hwphysicstech,
    • 20 replies
    • 1.6k views

  8. Cura Slicer issue with Benchy

    By dodgefan3737,
    • 1 reply
    • 1.7k views

  9. Issue with curved surfaces in cura 4.7

    By aarab1988,
    • 1 reply
    • 1.9k views

  10. Initial Layer Smearing Through Small Holes

    By skjbTHI,
    • 12 replies
    • 2.3k views

  11. Help with printing a dome

    By Ten,
    • 0 replies
    • 871 views

  12. Issue with Cura Ironing

    By Nir152,
    • 0 replies
    • 1.3k views

  13. Good first few layers followed by under extrusion

    By huub8,
    • 1 reply
    • 411 views

  14. Slice Hollow part with open end

    By pander1405,
    • 6 replies
    • 1k views

  15. Internal supports on a hollow form

    By Dbradbury,
    • 1 reply
    • 1.6k views

  16. ABS printing with a gcode pause for nut insertion

    By cbrayton,
    • 3 replies
    • 636 views

  17. Help: Trying to print models on top each other

    By DomXDOTMulita,
    • 0 replies
    • 634 views

  18. Help top surface squiggle lines and blobs

    By huggibunni,
    • 0 replies
    • 601 views

  19. €10 for slicing 600MB STL in Cura anyone?

    By bltouchdude,
    • 0 replies
    • 573 views

  20. Bigger Prints

    By ccookson60,
    • 4 replies
    • 782 views

  21. Cura help for last layer on top

    By huggibunni,
    • 2 replies
    • 711 views

  22. TPU printing

    By krknopp,   
    • 1 reply
    • 1.5k views

  23. Strange Zits and Blobs on #3D Benchy

    By Brenttnerb,
    • 1 reply
    • 4k views

  24. I need hepp fixing corner and surface issues on a print.

    By Anafear,
    • 4 replies
    • 467 views

  25. Having a terrible time printing a certain print.. could really use help.

    By TinaBakir1210,
    • 5 replies
    • 557 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 20 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...