Jump to content

Deutsch

Herzlich willkommen im deutschsprachigen Forum

3,184 topics in this forum

  1. Einzugstropfen deaktivieren Cura

    By Timmel93,   
    • 3 replies
    • 813 views

  2. Anycubic i3 Mega S ................ Temperatur 0°

    By Haegar7,   
    • 12 replies
    • 1.5k views

  3. Hallo zusammen habe mein Start/end code gelöscht wie kann Mann es wieder rügärig machen und den start/end code kopieren in cura

    By sam77,   
    • 4 replies
    • 521 views

  4. Z-Geschwindigkeit

    By Allrounder,   
    • 7 replies
    • 466 views

  5. Mainboard S5 R2

    By Alf,   
    • 0 replies
    • 327 views

  6. Ultimaker braucht sehr lange zum Start

    By 11102022,   
    • 6 replies
    • 910 views

  7. Linienabstand top layer

    By Goldmann,   
    • 0 replies
    • 295 views

  8. Cura 5.1 - Lücken im Druck

    By KaiV,   
    • 6 replies
    • 1k views

  9. Erste Schicht in Cura unvollständig

    By hodenklaus,   
    • 4 replies
    • 885 views

  10. Druck zerfällt in Schichten 1 2

    By Larissa,
    • 28 replies
    • 12k views

  11. Position Z Naht

    By Leporello,   
    • 6 replies
    • 2.7k views

  12. Druckqualität Ultimaker S Line vs Ultimaker 3

    By RaphaelOst,   
    • 3 replies
    • 784 views

  13. Ultimaker 2+ macht einen Filament-Blob auf den fertigen Druck

    By BigLebowski,   
    • 19 replies
    • 941 views

  14. Druck ohne xy-Bewegung pausieren

    By spodec90,   
    • 1 reply
    • 418 views

  15. Ultimaker Cura Bauraum fixiert

    By Krishan,   
    • 3 replies
    • 507 views

  16. Prime Tower

    By BastelWastel,   
    • 8 replies
    • 1.6k views

  17. Ultimaker S5 im Netzwerk von jedem sichtbar - Passwortschutz o.ä. möglich?

    By PatrickS1990,   
    • 13 replies
    • 1.3k views

  18. Cura ab Version 5 hängt sich auf

    By SchnubbelCube,   
    • 3 replies
    • 705 views

  19. Stützstrukturschnittstelle Extra Druck Beta 5.2.0

    By Ksstyling,   
    • 0 replies
    • 296 views

  20. Druckgeschwindigkeit suche hilfe

    By BUSCHFLEXER,   
    • 1 reply
    • 389 views

  21. Ich werde noch verückt :D der S5 macht was er will :D Wieder mal Niverlierungssensor UPDATE :D Neuer Lüfter

    By Ksstyling,   
    • 9 replies
    • 566 views

  22. Speicherort für Druckprofile ändern

    By HofmannM,
    • 1 reply
    • 1.5k views

  23. Einzelne Punkte in der Außenhaut

    By Felsentreu,   
    • 4 replies
    • 469 views

  24. Cura 5.1.1 startet nicht

    By manau21,   
    • 6 replies
    • 3.7k views

  25. Ultimaker 2+, in Cura keine Drucktemperatur Einstellung

    By Felsentreu,   
    • 10 replies
    • 915 views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...