Jump to content

Français

Bienvenue sur le forum francophone

2,706 topics in this forum

  1. mauvaise adhérence sur plateau chauffant sur ultimaker 2 extended +

    By draeni,
    • 7 replies
    • 1.5k views

  2. problème: intérieur dentelé 1 2

    By caro,
    • 32 replies
    • 4.2k views

  3. Décoller la couche sous la pièce après impression (pièce enlevée du plateau)

    By skullofcob,
    • 12 replies
    • 6.6k views

  4. Heater error

    By kristof06,
    • 4 replies
    • 1.3k views

  5. Mise a firmware cura 2.3.1

    By kryscosne,
    • 2 replies
    • 2.1k views

  6. nouvelle buse Olsson RUBY

    By kryscosne,
    • 3 replies
    • 1.6k views

  7. Fichier de configuration (.xml)

    By Fray,
    • 0 replies
    • 1.1k views

  8. Faire un leveling d'une delta avec Cura ?

    By kokam,
    • 3 replies
    • 2k views

  9. Débuts en impression 3D avec la main Enable

    By Pseudoto,
    • 5 replies
    • 1.6k views

  10. Varier l'épaisseur des couches.

    By Ju_bil,
    • 7 replies
    • 4k views

  11. Impression ABS... je craque !

    By roban,
    • 20 replies
    • 19.9k views

  12. Bonjour ! 1mm nozzle best printing settings ?

    By antoine-cr,
    • 8 replies
    • 2.8k views

  13. Bug en fin d'impression

    By sleve,
    • 1 reply
    • 1k views

  14. délaminage avec du XT

    By francois1,
    • 8 replies
    • 1.2k views

  15. Pourquoi je perd toutes mes affaires ! 1 2

    By zizon,
    • 26 replies
    • 4k views

  16. une maquette entierement imprimée avec une ultimaker 2

    By glut,
    • 9 replies
    • 2.6k views

  17. Fermer une UM2 & retour d'expérience

    By ultimprint,
    • 18 replies
    • 2k views

  18. Mesures impresises

    By jmgill,
    • 23 replies
    • 3.4k views

  19. Vitesse d'impression ABS

    By Patato,
    • 5 replies
    • 1.7k views

  20. Problème de lâcher de matière lors de voyage "trait bleu sous CURA"

    By nono16,
    • 8 replies
    • 2.8k views

  21. Sous-extrusion sur la première couche

    By Armatus,
    • 13 replies
    • 5k views

  22. Claquements UM2GO

    By freyjamir,
    • 15 replies
    • 1.4k views

  23. Carte Ultimaker 2 transistors 100-35V-RVT qui ont bruler

    By supernovaixi,
    • 4 replies
    • 1.7k views

  24. Molette de selection Ultimaker 2

    By fredlime,
    • 5 replies
    • 1.5k views

  25. Fiber printing one

    By rigs,
    • 6 replies
    • 1.2k views

  • Our picks

    • Introducing the UltiMaker Factor 4

      Introducing the UltiMaker Factor 4

      ArunC posted a topic in UltiMaker 3D printers,

      We are happy to announce the next evolution in the UltiMaker 3D printer lineup: the UltiMaker Factor 4 industrial-grade 3D printer, designed to take manufacturing to new levels of efficiency and reliability. Factor 4 is an end-to-end 3D printing solution for light industrial applications
      • 3 replies
      MariMakes

      Picked By

      MariMakes,
    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 26 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...