Jump to content

Improve your 3D prints

Help, tips & tricks

5,372 topics in this forum

  1. UM2 Bed Temperature reading higher than actual temperature

    By idesignmake,   
    • 4 replies
    • 673 views

  2. Vase mode without seam

    By ManlishPotato,   
    • 23 replies
    • 6.9k views

  3. Making loud noise when starting a print

    By jechsturk,   
    • 2 replies
    • 2k views

  4. UM PVA snapping in bowden tubes

    By aoeng,   
    • 8 replies
    • 1.2k views

  5. Self leveling passes but nozzle prints too high

    By jls123,
    • 7 replies
    • 884 views

  6. X axis does not go to home position at start of print

    By w6lsu,
    • 2 replies
    • 771 views

  7. Cura manual question

    By awmdaj,
    • 3 replies
    • 723 views

  8. 3D printing models problems! HELP!

    By simaomanoel,   
    • 5 replies
    • 642 views

  9. Unfinished prints with new profile

    By ist165351,
    • 0 replies
    • 324 views

  10. My Ultimaker 2+ stops in the middle of a print

    By andyburke1980,   
    • 4 replies
    • 2.1k views

  11. filament extrusion slow but not zero

    By tilmanlampartter,   
    • 5 replies
    • 1.7k views

  12. Cura Speed Setting issue

    By mmsg,
    • 0 replies
    • 590 views

  13. cura engine question

    By awmdaj,
    • 1 reply
    • 344 views

  14. Gaps in shell after slicing

    By willryan3,   
    • 2 replies
    • 957 views

  15. Bad prints after changing PLA

    By haroldjclements,   
    • 3 replies
    • 479 views

  16. UM s5 - Fast Print 0.8mm Nozzle?

    By danieledge123,
    • 0 replies
    • 696 views

  17. Crazy behavior after first layer.

    By SPatVT,   
    • 3 replies
    • 557 views

  18. Editing blocks of a model

    By Buzzed1971,   
    • 3 replies
    • 2.5k views

  19. Retraction from prime tower to part

    By willryan3,
    • 9 replies
    • 795 views

  20. Clogged/Stuck AA Nozzle Hot Cold Pulls not working

    By arthurmsarthur,
    • 1 reply
    • 726 views

  21. 3D Printer stops in the middle of a print

    By andyburke1980,   
    • 0 replies
    • 632 views

  22. Banding in the Z at feature change

    By JDM3D,   
    • 0 replies
    • 657 views

  23. Printer not working after Cura update.

    By gabgomez,
    • 1 reply
    • 588 views

  24. Does anyone have any good settings for Inland PETG using painters tape on the bed?

    By mbaram,
    • 6 replies
    • 5k views

  25. Sudden issue printing with 0.8mm nozzle

    By JonGregory,   
    • 1 reply
    • 1.3k views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 20 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...