Jump to content

Deutsch

Herzlich willkommen im deutschsprachigen Forum

3,185 topics in this forum

  1. Beratung 3D-Scanner

    By ingo46,   
    • 3 replies
    • 549 views

  2. QiDi X-Plus Drucker in Cura benutzen

    By RKR,   
    • 1 reply
    • 4.8k views

  3. Cura Error

    By Golf3gti1,   
    • 0 replies
    • 358 views

  4. Probleme bei Stützstruktur mit PVA

    By Hering95,   
    • 2 replies
    • 1.3k views

  5. Filament bleibt einfach nicht richtig kleben...

    By DanielDerStolle,   
    • 15 replies
    • 7.5k views

  6. UM2Connect - Druck mit Raft

    By JeaperCreeper,   
    • 2 replies
    • 574 views

  7. Sehr lange Startzeit - kann man das verkürzen?

    By Lupus52,   
    • 20 replies
    • 1.8k views

  8. Ultimaker S5 > Tough PLA > Druckprobleme auf beiden Köpfen

    By Bergfruehling,   
    • 5 replies
    • 1.3k views

  9. Ultimaker 3 Löcher zwischen Wand und Füllung

    By RaphaelOst,   
    • 17 replies
    • 2.3k views

  10. Verschiedene Filamente / Farben drucken mit Materialstation

    By Testdruck0815,   
    • 2 replies
    • 765 views

  11. Stützstrukturblocker funktioniert nicht richtig

    By Felsentreu,   
    • 10 replies
    • 1.3k views

  12. Fehler im Infill bei BASF Ultrafuse 316L und Ultimaker S5 Pro Bundle

    By scs34,   
    • 7 replies
    • 1.1k views

  13. RF2000 als Custom FFF Printer bei Cura hinzufügen

    By Carinih,
    • 1 reply
    • 2.1k views

  14. Cura zerreißt die Oberfläche und setzt die Supports nicht

    By wolff80,   
    • 3 replies
    • 485 views

  15. Programmabbruch wenn Anycubic Chiron ausgewählt wird

    By KMiggi,   
    • 2 replies
    • 460 views

  16. Ultimaker 2+ auf dual umrüsten?

    By maia23,   
    • 21 replies
    • 3.3k views

  17. Ulti 2 heater error

    By schneck007,   
    • 21 replies
    • 827 views

  18. Druck wird bei ca. 6mm verschoben

    By miti937,   
    • 2 replies
    • 534 views

  19. Profil Geeetech A30T/ Probleme mehrfarbdruck

    By djseppo,   
    • 6 replies
    • 2k views

  20. S5 macht seit kurzem Probleme beim Druck mit PETG

    By lowrey,   
    • 14 replies
    • 989 views

  21. Cura lässt sich nicht öffnen nach Grafikkartentausch

    By shadow1606,   
    • 3 replies
    • 725 views

  22. Füllstand einer Spule auslesen ohne sie komplett zu laden bzw. per Handy?

    By Lefherz,   
    • 23 replies
    • 1.4k views

  23. Cura / Vyper / Startpunkt nach Änderung Gcode

    By YvonneP,   
    • 1 reply
    • 557 views

  24. Ultimaker S3 Lift Switch Probleme

    By RaphaelOst,   
    • 8 replies
    • 1k views

  25. Drucker S5 druckt nicht mehr

    By Heysteyn,   
    • 10 replies
    • 1.4k views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
        • Like
      • 26 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
        • Like
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...