Jump to content

Deutsch

Herzlich willkommen im deutschsprachigen Forum

3,184 topics in this forum

  1. Flsun QQ

    By IMB,
    • 2 replies
    • 3.3k views

  2. Temperatur UM3 260 Grad an Düse ?

    By micpic,
    • 3 replies
    • 1.5k views

  3. 3d Solex / Carbon Erfahrungsbericht

    By micpic,   
    • 1 reply
    • 2.4k views

  4. Ultimaker setzt am Ende einen Batzen Filament drauf 1 2

    By remars,
    • 43 replies
    • 6.1k views

  5. Ultimaker 2 Extended Druckbalken hängt

    By Ultimulti_1234,   
    • 2 replies
    • 533 views

  6. Anfang der ersten Linie erzeugt immer ein kleines Loch

    By Bsp91,   
    • 3 replies
    • 1.2k views

  7. Profil für Flex Material von Ultimaker gesucht

    By Produktdesigner,
    • 7 replies
    • 1.1k views

  8. Ultimaker 2+ druckt die letzten Layer in der Luft

    By JanWhite,   
    • 8 replies
    • 1.1k views

  9. verschobene layer beim drucken

    By sebastian21,   
    • 5 replies
    • 895 views

  10. Abstände in Modellen vergrößern

    By Chrischan,   
    • 5 replies
    • 1.6k views

  11. Ultimaker 2+ Feedermotor läuft verkehrt

    By KaiserNero,   
    • 6 replies
    • 1.9k views

  12. Anycubic I3 Mega Druckhöhe Z Achse

    By TimMueller,   
    • 16 replies
    • 11.8k views

  13. UM 2 kaputt?

    By JB_Sullivan,   
    • 14 replies
    • 2.9k views

  14. Unable to slice

    By designhub,
    • 4 replies
    • 3.8k views

  15. UM3 druckt nicht zweifarbig

    By xxjudiith,   
    • 0 replies
    • 721 views

  16. Slicing mit Cura 2.3.1 brícht immer wieder ab

    By Dampflokfan,
    • 1 reply
    • 1.2k views

  17. Linienbreite erste Schicht vs horizontale Erweiterung erste Schicht

    By 3D-Simon,
    • 4 replies
    • 6.4k views

  18. Drucker macht schlechtes Druckerergebnis nach einigen Minuten

    By Produktdesigner,
    • 7 replies
    • 704 views

  19. welchen Print Core für HIPS als Stützmaterial ?

    By 3D-Simon,
    • 5 replies
    • 1k views

  20. Düse für UMO+

    By PhilDesign,   
    • 3 replies
    • 886 views

  21. Unterste Lage immer aus Stützmaterial, möglich ?

    By 3D-Simon,
    • 5 replies
    • 1k views

  22. Material Hinzufügen

    By KaiserNero,
    • 11 replies
    • 5.4k views

  23. Printcore UM3 und UMS5

    By Digibike,
    • 8 replies
    • 1.1k views

  24. Unterschiedliche Druckeinstellung bei einem Print CURA

    By TimMueller,   
    • 5 replies
    • 5.8k views

  25. Ultimaker 2+ hängt sich auf

    By remars,
    • 10 replies
    • 2.4k views

  • Our picks

    • UltiMaker Cura 5.7 stable released

      UltiMaker Cura 5.7 stable released

      ArunC posted a topic in UltiMaker Cura,

      Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
       
      • 18 replies
      MariMakes

      Picked By

      MariMakes,

    • Release Notes: S-Line Firmware 8.3.0 (Latest)

      Dustin posted a topic in Firmware,

      S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
      (Sorry, was out of office when this released)

      This update is for...
      All UltiMaker S series  
      New features
       
      Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
      • 0 replies
      MariMakes

      Picked By

      MariMakes,
    View All
×
×
  • Create New...